Long-Term Supported Versions

    Innovation Versions

      Kernel Parameters

      Hardening the Security of Kernel Parameters

      Description

      Kernel parameters specify the status of network configurations and application privileges. The kernel provides system control which can be fine-tuned or configured by users. This function can improve the security of the OS by controlling configurable kernel parameters. For example, you can fine-tune or configure network options to improve system security.

      Implementation

      1. Write the hardening items in Table 1 to the /etc/sysctl.conf file.

        NOTE:
        Record security hardening items as follows:

        net.ipv4.icmp_echo_ignore_broadcasts = 1  
        net.ipv4.conf.all.rp_filter = 1  
        net.ipv4.conf.default.rp_filter = 1  
        

        Table 1 Policies for hardening the security of kernel parameters

        Item

        Description

        Suggestion

        Configured as Suggested

        net.ipv4.icmp_echo_ignore_broadcasts

        Specifies whether ICMP broadcast packets are accepted. They are not accepted according to the hardening policy.

        1

        Yes

        net.ipv4.conf.all.rp_filter

        Specifies whether the actual source IP address used by a data packet is related to a routing table and whether the data packet receives responses through interfaces. The item is enabled according to the hardening policy.

        1

        Yes

        net.ipv4.conf.default.rp_filter

        1

        Yes

        net.ipv4.ip_forward

        The IP forwarding function prevents unauthorized IP address packets from being transferred to a network. The item is disabled according to the hardening policy.

        0

        Yes

        net.ipv4.conf.all.accept_source_route

        accept_source_route indicates that a packet sender can specify a path for sending the packet and a path for receiving a response. The item is disabled according to the hardening policy.

        0

        Yes

        net.ipv4.conf.default.accept_source_route

        0

        Yes

        net.ipv4.conf.all.accept_redirects

        Specifies whether a redirected ICMP packet is sent. The packet is not sent according to the hardening policy.

        0

        Yes

        net.ipv4.conf.default.accept_redirects

        0

        Yes

        net.ipv6.conf.all.accept_redirects

        0

        Yes

        net.ipv6.conf.default.accept_redirects

        0

        Yes

        net.ipv4.conf.all.send_redirects

        Specifies whether a redirected ICMP packet is sent to another server. This item is enabled only when the host functions as a route. The item is disabled according to the hardening policy.

        0

        Yes

        net.ipv4.conf.default.send_redirects

        0

        Yes

        net.ipv4.icmp_ignore_bogus_error_responses

        Fake ICMP packets are not recorded to logs, which saves disk space. The item is enabled according to the hardening policy.

        1

        Yes

        net.ipv4.tcp_syncookies

        SYN attack is a DoS attack that forces system restart by occupying system resources. TCP-SYN cookie protection is enabled according to the hardening policy.

        1

        Yes

        kernel.dmesg_restrict

        Hardens dmesg messages. Only the administrator is allowed to view the messages.

        1

        Yes

        kernel.sched_autogroup_enabled

        Determines whether the kernel automatically groups and schedules threads. After this item is enabled, scheduling groups compete for time slices, and threads in a scheduling group compete for the time slices allocated to the scheduling group. The item is disabled according to the hardening policy.

        0

        No

        kernel.sysrq

        Disables the magic key.

        NOTE:

        You are advised to disable the magic key so that commands cannot be directly passed to the kernel.

        0

        Yes

        net.ipv4.conf.all.secure_redirects

        Specifies whether redirected ICMP messages sent from any servers or from gateways listed in the default gateway list are accepted. Redirected ICMP messages are received from any servers according to the hardening policy.

        0

        Yes

        net.ipv4.conf.default.secure_redirects

        0

        Yes

      2. Run the following command to load the kernel parameters set in the sysctl.conf file:

        sysctl -p  /etc/sysctl.conf
        

      Other Security Suggestions

      • net.ipv4.icmp_echo_ignore_all: ignores ICMP requests.

        For security purposes, you are advised to enable this item. The default value is 0. Set the value to 1 to enable this item.

        After this item is enabled, all incoming ICMP Echo request packets will be ignored, which will cause failure to ping the target host. Determine whether to enable this item based on your actual networking condition.

      • net.ipv4.conf.all.log_martians/net.ipv4.conf.default.log_martians: logs spoofed, source routed, and redirect packets.

        For security purposes, you are advised to enable this item. The default value is 0. Set the value to 1 to enable this item.

        After this item is enabled, data from forbidden IP addresses will be logged. Too many new logs will overwrite old logs because the total number of logs allowed is fixed. Determine whether to enable this item based on your actual usage scenario.

      • net.ipv4.tcp_timestamps: disables tcp_timestamps.

        For security purposes, you are advised to disable tcp_timestamps. The default value is 1. Set the value to 0 to disable tcp_timestamps.

        After this item is disabled, TCP retransmission timeout will be affected. Determine whether to disable this item based on the actual usage scenario.

      • net.ipv4.tcp_max_syn_backlog: determines the number of queues that is in SYN_RECV state.

        This parameter determines the number of queues that is in SYN_RECV state. When this number is exceeded, new TCP connection requests will not be accepted. This to some extent prevents system resource exhaustion. Configure this parameter based on your actual usage scenario.

      Bug Catching

      Buggy Content

      Bug Description

      Submit As Issue

      It's a little complicated....

      I'd like to ask someone.

      PR

      Just a small problem.

      I can fix it online!

      Bug Type
      Specifications and Common Mistakes

      ● Misspellings or punctuation mistakes;

      ● Incorrect links, empty cells, or wrong formats;

      ● Chinese characters in English context;

      ● Minor inconsistencies between the UI and descriptions;

      ● Low writing fluency that does not affect understanding;

      ● Incorrect version numbers, including software package names and version numbers on the UI.

      Usability

      ● Incorrect or missing key steps;

      ● Missing prerequisites or precautions;

      ● Ambiguous figures, tables, or texts;

      ● Unclear logic, such as missing classifications, items, and steps.

      Correctness

      ● Technical principles, function descriptions, or specifications inconsistent with those of the software;

      ● Incorrect schematic or architecture diagrams;

      ● Incorrect commands or command parameters;

      ● Incorrect code;

      ● Commands inconsistent with the functions;

      ● Wrong screenshots.

      Risk Warnings

      ● Lack of risk warnings for operations that may damage the system or important data.

      Content Compliance

      ● Contents that may violate applicable laws and regulations or geo-cultural context-sensitive words and expressions;

      ● Copyright infringement.

      How satisfied are you with this document

      Not satisfied at all
      Very satisfied
      Submit
      Click to create an issue. An issue template will be automatically generated based on your feedback.
      Bug Catching
      编组 3备份